Why is my mix quieter than pro tracks - LUFS, gain staging and limiting

Why Is My Mix Quieter Than Pro Tracks?

Your mix peaks right below 0 dB. You drop a commercial track next to it and yours sounds small, flat and quiet. You push the limiter harder, and now it's loud - but it pumps, the kick shrinks and the highs start to hurt.

Here is the thing: loudness is not the same as peak level. Two tracks can both peak at -1 dB and one still sounds twice as loud. What decides it is how much energy sits between the peaks - and that is mostly decided in the mix, not on the master.

In this guide we at Blue Turtle Audio show you why your mix sounds quieter, how to measure it properly and the order we use to get loud without wrecking the punch. With start values you can use tonight.

Stop Guessing, Start Mixing - free mixing guide PDF by Blue Turtle Audio

FREE MIXING GUIDE

Want a mix that's loud and still punchy?

Get our free Mixing Guide: 5 of the most important fixes - headroom, kick and bass, mud, punch and more. Start values for any DAW.

Get the free guide →

By signing up you agree to receive free packs and offers by email - unsubscribe anytime, see our Privacy Policy.

Get the Bundle - save 27 %

Free 11-page PDF. No checkout, no payment.

Related tutorials:

What is loudness, and what are we fixing?

Your DAW meter shows peak level: the single loudest sample. Your ears hear average energy over time. That is what LUFS (Loudness Units relative to Full Scale) measures. A mix with big, spiky peaks and little energy between them hits the ceiling early and sounds quiet. A mix with controlled peaks can be turned up much further before anything clips.

Three numbers matter: integrated LUFS (loudness of the whole track), short-term LUFS (the last 3 seconds, useful for the drop) and true peak in dBTP (the real peak after conversion, which can sit slightly above the sample peak).

What we're using

  • Any DAW (values below work in Ableton Live, FL Studio, Logic and others)
  • A loudness meter: Logic's stock Loudness Meter, or the free Youlean Loudness Meter in any DAW
  • A stock limiter and a soft clipper or saturator
  • One commercial reference track in your genre

Where your track stands

Integrated loudness: typical numbersRough mix, no limiterabout -18 to -14 LUFSApple Music plays at-16 LUFSSpotify / YouTube play at-14 LUFSMelodic techno releaseoften -10 to -8 LUFSHouse / techno club masteroften -9 to -6 LUFSTypical ranges, not targets. Streaming services turn louder tracks down to their reference level.
The gap between a rough mix and a club master is often 6-10 dB of loudness - not something one plugin should fix alone.

1. Fix the loudness problems in the mix

Leave headroom on the mix bus

Mix with the master fader at 0 and no limiter on the mix bus. Start with the kick: set it so it peaks around -6 dBFS on its own, then build the mix around it and keep the mix bus peaking around -6 to -3 dBFS. This sounds backwards, but it gives every later step room to work.

The low end eats your loudness

Bass frequencies carry the most energy. A sub that's too loud, wide stereo below 120 Hz, or kick and bass hitting at the same time will hit the limiter first and push everything else down. High-pass everything that doesn't need lows (pads, leads, vocals, FX - start around 100-150 Hz), keep the sub mono and get the kick-bass balance right before you think about loudness.

Pro tip: Turn your whole mix down 10 dB and listen. If the kick and bass still sound balanced at low volume, the limiter will have an easy job later. If the low end disappears or takes over, fix that first.

Tame the peaks track by track

Spiky drums are the classic reason a mix can't get loud. A clipper or saturator on the drum bus that shaves 1-2 dB off the transients is often inaudible on its own, but it gives you that 1-2 dB back at the end. Same idea for a snare or clap with a hard click: a fast compressor or clipper taking 2-3 dB off the peak.

Where What Start values
Mix bus No limiter while mixing Peaks -6 to -3 dBFS
Kick Set first, mix around it Peaks around -6 dBFS
Non-bass tracks High-pass 100-150 Hz, then by ear
Low end Mono Below about 120 Hz
Drum bus Soft clip / saturate Shave 1-2 dB off the peaks
Harsh tracks Cut 2-5 kHz 2-3 dB, wide bell

2. Get loud the clean way

Use stages, not one hard limiter

Every stage takes a little: a bus compressor glues, a clipper shaves the loudest peaks, the limiter catches the rest. Three stages doing 1-3 dB each sound far cleaner than one limiter doing 8 dB.

The loudness chain on the master1Mix busPeaks -6 to -3 dBFS2Glue comp2:1, 1-2 dB reduction3ClipperShave 1-2 dB of peaks4Limiter2-4 dB, ceiling -1 dBTP5MeterIntegrated + short-term6ReferenceLevel-matched A/B
Small amounts per stage. If one stage has to work hard, go back to the mix.

Set the limiter

Ceiling at -1 dBTP (true peak), so the track doesn't clip after MP3 or AAC encoding. Raise the input until you see 2-4 dB of gain reduction on the loudest parts. Release on auto, or start around 50-150 ms. Listen to the kick: as soon as it gets smaller or the hi-hats start to pump, back off by 1 dB.

DAW Glue / bus comp Clip / saturate Limit and meter
Ableton Live Glue Compressor Saturator (Soft Clip) Limiter, plus a free loudness meter
FL Studio Fruity Limiter (COMP mode) Fruity Soft Clipper Fruity Limiter or Maximus, plus a free loudness meter
Logic Pro Compressor (VCA model) Clip Distortion, gently Adaptive Limiter + Loudness Meter
Pro tip: Insert the meter after the limiter and read short-term LUFS in the drop, not only integrated LUFS. Breakdowns pull the integrated number down, the drop is what people compare.

3. Now that it's loud, what's next?

Compare at the same loudness

Louder always sounds better at first. To judge your master honestly, turn the reference down until both read the same short-term LUFS. Now compare punch, low end and brightness. If the reference still sounds bigger, the difference is in the mix, not in the limiter.

Know what streaming does

With loudness normalization switched on, Spotify and YouTube play tracks at about -14 LUFS and Apple Music at about -16 LUFS. A master at -7 LUFS is simply turned down. That's why a crushed master can sound smaller on Spotify than a dynamic one: same loudness after normalization, but less punch. For club and DJ use, louder masters are still common - just don't buy loudness with distortion.

Common mistakes

  • Limiting on the mix bus from the start and mixing into it.
  • Checking only the integrated LUFS and ignoring the drop.
  • Wide stereo subs and too much low end eating the headroom.
  • Pushing the limiter until the kick loses its punch.
  • Comparing to a reference that is louder than your mix.

FAQ: making your mix louder

What LUFS should I master to?

There is no single number. For streaming, anything between about -14 and -9 LUFS integrated works, because louder tracks get turned down. For club tracks in house and techno, many releases land around -9 to -6 LUFS. Pick the loudness where your track still punches.

Why does my track sound smaller after limiting?

The limiter is working too hard on the transients - usually because the mix sends too much low end or spiky drums into it. Take 1-2 dB off with a clipper on the drum bus and less sub, then limit less.

Does Spotify make my track quieter?

Only if it is louder than its reference of about -14 LUFS and normalization is on (the default). Then it turns the whole track down. Your dynamics stay the same - which is why punchy masters often win after normalization.

Should I mix with a limiter on the master?

Better not. Mix into headroom, then add the loudness chain at the end. If you want to hear roughly how the master will sound, use a limiter on a reference bus or switch it on only for checks.

MAKE YOUR MIX LOUD - AND CLEAN.

Stop Guessing, Start Mixing - free mixing guide PDF by Blue Turtle Audio

FREE MIXING GUIDE

5 of the most important fixes for a clean, punchy mix

Headroom, frequency map, kick and bass, mud and punch - one page per problem, with start values and a quick test. Works in every DAW.

Get the free guide →

By signing up you agree to receive free packs and offers by email - unsubscribe anytime, see our Privacy Policy.

Get the Bundle - save 27 %

Free 11-page PDF. No checkout, no payment.

More tutorials:

Greetings & Have Fun! Your Blue Turtle Audio Team.

Back to blog